hmmm...I kept the one from Ford Performance that I'd bought for my FE (new owner didn't value it)...and figured I'd use it on the BRap. I hadn't even considered that it wouldn't fit.
What did you do to your Bronco Raptor today?
- Thread starter Dragoon
- Start date
- May 25, 2022
- 555
- Gallery
- 266
- 1,377
- Current Ride
- 2022 Bronco Raptor
- Current Ride #2
- 2023 Land Rover Defender 110
Today on the season finale (probably not actually) of “What Did With Do WithYour Bronco Raptor Today?” Randy completes his winch project.
The mounting, reassemble and spooling went pretty smoothly, but I forgot to put the silver plastic front cover on before mounting the winch plate, winch and cable routing. Other Broncos have two separate panels that mount on each side of the tow points, while the Raptor‘s single piece loops over the top. Fortunately, after suffering an oh sh*t moment or two, I realized I could just unbolt the six bolts on the winch plate, lift the assembly and slip the cover in. Crisis averted.
and there were a few choice words threading rope and inserting the puck in the winch. Hated that each time I’ve done it.
But it’s all done with minimal drama, it works (always a bonus) and I only have a little bit of cable / sprayer hose management left to do.
Nice Job!
Is the next episode back into the snowy mountains testing the Winch? 
Your front camera now is really at the front.
DallasCajun
Well-known member
I’ve seen feedback that the Ford/Bestop versions do fit but the crossbar is a question. JTops has made it clear that theirs doesn’t fit and you can see why when you watch the install video. It has to do with removing the hardtop bracket (where the Braptor cross-brace is located) and how the mesh is attached at that point. The Ford/Bestop version has a cross-bar in that same area, but I’m not sure if there’s an interference or not for those versions.
OP
- Thread Starter
- Thread starter
- #45
That turned out great! I think you might be one of the first Bronco Raptors with a winch on it. That front camera is now truly front and center!
- May 25, 2022
- 555
- Gallery
- 266
- 1,377
- Current Ride
- 2022 Bronco Raptor
- Current Ride #2
- 2023 Land Rover Defender 110
I should have done a check before and after on approach angle using my highly flawed method pictured below. While it still wouldn’t be accurate at least it would be consistently measured inaccurately!
I think the. OEM approach angle is 47 degrees I’d put this around 43 degres +/- some margin of error.
Actually mines probably even a little less if I fully factored in my flatlink and rope guard.
Hope that helps in some way.
Yes that's very informative. Actually I would have expected more impact - 42-43 degrees is still really good.
If there is a need to restore the approach angle close to factory, a front leveling kit may do the trick... or larger tires.
OP
- Thread Starter
- Thread starter
- #50
That is very visual and super helpful, thanks for sharing!
NDRaptor
Member
What did I do today…..looked at my picture off the assembly line and kept doing countdown math to between Feb 7 and 13th at my dealer. Just 1 piece of this process to be on or ahead of schedule would be super noice. All the while tripping over a stack of go fast and off road goodies in the garage.
Having a beer now…….trolling, dreaming, obsessing, man-crushing. Honesty is the best policy. Have a good weekend.
Having a beer now…….trolling, dreaming, obsessing, man-crushing. Honesty is the best policy. Have a good weekend.
Attachments
OP
- Thread Starter
- Thread starter
- #52
Today I added a full set of Dash Caddies from Sinister Speed Shop and a MagSafe phone mount to an accessory arm from the accessory mount on the dash.
OP
- Thread Starter
- Thread starter
- #53
Yesterday I installed lower rocker PPF from Underground Graphics to help save the bottom sections of the doors from rock chips. The PPF needs to be trimmed around the portion of the fender flare on the rear doors since this kit is designed for the standard Bronco. A fresh razor blade made it easy to trim and slightly tuck under the flare piece on the door.
DallasCajun
Well-known member
This damn thread keeps digging into my wallet...looking at ordering some of the PPF protection stuff for the hood and roll bars.
I added a magnet in an attempt to improve the charging pad performance! 
OP
- Thread Starter
- Thread starter
- #57
I used a plug tap I got off Amazon and mounted my Valentine One radar detector using the directions found here:
www.broncoraptor.com
Here's the link to the mirror tap I used: https://amzn.to/3REAHTr
Bronco Raptor Radar Detector Mount and Mirror Tap
I recently upgraded my Valentine V1 to the Gen 2 model and mounted it in my 2021 Bronco Badlands using the standard Valentine V1 radar detector suction cup mount and a mirror tap kit I got off Amazon. Here's a link to the kit I used: https://amzn.to/40LXHV5 I chose that kit because it offered...
www.broncoraptor.com
Here's the link to the mirror tap I used: https://amzn.to/3REAHTr
Last edited by a moderator:
DallasCajun
Well-known member
I never knew something like this existed...but there's another $15 'invested' in my Braptor. Love the idea!I added a magnet in an attempt to improve the charging pad performance!
Definitely better than without, but still not perfect. A good jolt can still knock it off the magnet…
Installed windshield banner, these are available from Lethal Performance in 3 colors for less than directly from Ford Performance.
Note, in case someone notices, roof panels are not latched down as my BR is in winter storage
Note, in case someone notices, roof panels are not latched down as my BR is in winter storage
